Quake3World

Hi, could somewone please tell me how to make the game to show the FPS?

THANKS

cg_drawfps 1

/cg_drawFPS 1

edit:

Thanks, now I have another question:
there is a site with comands, variables etc
and i have some variables that i want to load or exec in the game, I'v creeated a text file and passed all the varables in there but when I try to exec the file it says: couldn't exec my config.cfg
(sorry foor my bad English)

make sure the file is saved as config.cfg and not something like config.txt.cfg
just make sure you have show hide extensions for known filetypes unchecked.

Thanks, that worked but It make my gun smaller and on the midle of the screen, any ideeas. I replaced the q3config.cfg with the original one and now its normal but i only have 24-35FPS with vsync off and refresh rate of 85HZ.
Any ideeas on how I could make the game run withat least 50FPS
Here are my curent settings:
in game rezolution 800x600@85Hz
16bit texture deph
high detail
I have a i815EP solano inyrgrated graphcs with 32MB

THANKS

Cristi wrote:Thanks, that worked but It make my gun smaller and on the midle of the screen, any ideeas. I replaced the q3config.cfg with the original one and now its normal but i only have 24-35FPS with vsync off and refresh rate of 85HZ.
Any ideeas on how I could make the game run withat least 50FPS
Here are my curent settings:
in game rezolution 800x600@85Hz
16bit texture deph
high detail
I have a i815EP solano inyrgrated graphcs with 32MB

THANKS

i'll let you find that variable. not sure what site you were using, but this is THE site for cmds and variables:

http://q3console.planetquake.gamespy.com/

Thats to one, I used the autoexec creeator to make the cfg file

Probably the only way to get more FPS is to run it more ugly.
You can also do a timedemo by dropping down the console (~).
Then type
/timedemo 1
Then type
/demo four
Demo four if your running point release 1.32

You could also give us you specs of your PC.
This is easly done using CPUZ.
You don't have to install the program, just extract it to a folder.
The click on the cpuz application icon.
It'll take a few seconds for it to load.
Once loaded, click on the about tab.
Now click on the HTML report and save it to your desktop.
Now simply upload it so we can see your system specs.
If you don't have any hosting site, I can host it for you, just send it to my hotmail account.

Here are my specs:

CPU-Z Report

--------------------------------------------------------------------------------

CPU-Z version 1.34.1.


CPU(s)
Number of CPUs 1

Name Intel Pentium III EB
Code Name Coppermine-T
Specification Intel Pentium III EB 1000MHz
Family / Model / Stepping 6 8 A
Extended Family / Model 0 0
Brand ID 2
Package Socket 370 FC-PGA
Core Stepping cD0
Technology 0.18 um
Supported Instructions Sets MMX, SSE
CPU Clock Speed 996.8 MHz
Clock multiplier x 7.5
Front Side Bus Frequency 132.9 MHz
Bus Speed 132.9 MHz
L1 Data Cache 16 KBytes, 4-way set associative, 32 Bytes line size
L1 Instruction Cache 16 KBytes, 4-way set associative, 32 Bytes line size
L2 Cache 256 KBytes, 8-way set associative, 32 Bytes line size
L2 Latency 0
L2 Speed 996.8 MHz (Full)
L2 Location On Chip
L2 ECC Check enabled
L2 Data Prefetch Logic no
L2 Bus Width 256 bits



Mainboard and chipset
Motherboard manufacturer Compaq
Motherboard model 0688h,
BIOS vendor Compaq
BIOS revision 686P2 v3.11
BIOS release date 10/23/2001
Chipset Intel i815/E/EP rev. A2
Southbridge Intel 82801BA (ICH2) rev. 01
Sensor chip SMSC 5D00




Memory
DRAM Type SDRAM
DRAM Size 512 MBytes
CAS# Latency 2.0 clocks
RAS# to CAS# 2 clocks
RAS# Precharge 2 clocks
Cycle Time (TRAS) 5 clocks
Bank Cycle Time (TRC) 7 clocks
# of memory modules 2
Module 0 Micron Technology SDRAM PC125 - 256 MBytes
Module 1 Micron Technology SDRAM PC133 - 256 MBytes



Software
Windows version Microsoft Windows XP Media Center Edition Professional Service Pack 2 (Build 2600)
DirectX version 9.0c

integrated 32mb graphics? eeesh. backup your current config, then remove all instances within the Quake III folder. then, go here and try these configs:

http://ucguides.savagehelp.com/Quake3/FPS_visuals.html

i got better fps than that with a pentium2 and 128MB sdram with a voodoo3. spend $30 and get yourself a geforce2 or something like that off pricewatch or froogle then fix your config and you could have 125fps on most maps.

do you speak french

Try here Sniper:
http://frenchfragfactory.net/forums/index.php

Sorry I don't undersrand french so good, a 815EP Graphics Chipset should only gine 28-30FPS , now I have 50, I don't have a AGP slot only PCI

Could you post that link in Engils because I dont understand so good French?

What the sweet fucking jesus is going on in this thread.

I'm all turned around Crink. Which way's The Void?